Harvester 1058H5 - Exterior


Information om kylare Information om kylare Information om hytten Information om hjulen Information om kran Information om aggregat

What is important for you?

Let us suppose that profitability is your top priority. Then you should know that the 1058H5 is built with the objective of low cost and high performance under severe conditions. High engine power and above all high torque at working speed supply large hydraulic force even when processing difficult trees.

The 1058H5 features fully 210 HP and 990 Nm already at low 1300 r.p.m.. The flow rate allows for quite high feed rates at a low relaxing engine speed. We also know that service is important to be able to work without facing problems. Thus we dispose of a well established service network.

The design as such is service-friendly too.

Further ergonomics are an important factor. The ergonomics of the 1058H5 allow for high working performance even at the end of a long working day.

These factors altogether result in a reliable machine with higher profitability.

 

For further information click on a square in the picture to the left or "Start guide"


Engine / Cooler

The engine is a step V without EGR valve. The after-treatment of the exhaust gases is done in a Single Module. It takes up less space, resulting in significantly decreased installation dimensions.

The cooling devices are positioned on the side instead of arranged in the front of the cabin and behind it. This results in a lower noise level in the cabin, while your visibility backwards becomes better.


Cranes

Two different reach lengths are available. The operator sits close to the crane and can easily follow the way of the harvester head between the trees up to full reach length.

This means less damage on the trunks and shorter crane cycles.


Wheels

Eight wheels and well balanced weight distribution will ease your way even under tough conditions on rough terrain.


Cabin

The driver´s cab is well positioned and has downward extended panes offering excellent visibility. You can see the wheels without having to lean out. .

The selection of trees does not require much effort, and the narrow posts permit perfect visibility during the processing.

Side lights low positioned on the cab enable you to lighten up the lateral surroundings of the machine.


Harvester Heads

Two different harvester heads can be attached to the boom.

Standard is the allround SP 561 LF harvester head. Cuts up to 60 cm felling dia. and is best suited for rough thinning and final cutting up to dbh 43 cm point to point delimbing dia.

The optional thinning head SP 451 LF cuts up to 53 cm felling dia. and is best suited for varying thinning up to dbh 35 cm point to point.


Information

  • Gremo 1058H5 features the same excellent weight distribution and low point of gravity as the previous machine. This means outstanding stability in all directions and allows for high-performance processing even in really tough terrain

    On sharp slopes down-hill work is feasible as long as the machine has grip. Climbing up-hill, of course, is easier with an 8-wheel equipped machine than one equipped with 4 or 6 wheels only.

  • Gremo 1058H5 owing to its 8 wheels and the excellent weight distribution is very gentle to the ground. It is outstanding on wet ground, as caterpillar chains can be put on both front and rear wheels.

    As standard the 1058H5 is supplied with 710/40x22.5 tyres.

  • The Gremo 1058H5 is normally furnished with the universal type harvester head SP 561 LF. This cuts up to 60 cm felling dia. and delimbs 43 cm point to point. It is suitable for rough thinning and final cutting work.

    The optional SP 451 harvester head is suitable for all types of thinning and manages also relatively big trees. It cuts 53 cm felling dia. and delimbs 35cm.

    Both harvester heads are equipped withLogHold, a patented system for holding the tree and with QuickCut for minimizing cutting cracks.

  • The unique stability is increased by the fact that all bogies during the processing are locked by the bogie-lift cylinders (standard). Bogielift with separate operation of righthand and lefthand bogies.

    This offers great versatility in tough terrain and increased flexibility compared to that supplied by smaller machines.

    The active bogie is one of our options. It enables extreme passability in very steep terrain.

  • The large downward extended window panes, the high upward extended side and rear window panes and the narrow poles offer excellent visibility across the whole working area.

    You can easily select the trees for processing, and you can see the wheels without having to lean out.

    And you have a good view of the ground in front of the machine.

    On the sides of the cabin there is low side lighting which allows you to illuminate the surroundings on both sides of the machine.

  • The strong and fast working parallel type boom is situated adjacent to the cab to enable you to follow the harvester head´s way through the trees.

    The crane holder provides a low center of gravity, while enabling very good visibility in the work area.

    Mesera 221H boom with 10 metres reach is standard, 11.1 m reach is optional.